Showing results: 2206 - 2220 of 2483 items found.
-
850 -
Ketai instrument (kunshan) Ltd.
This instrument is specially used for the forward, reverse and open phase inspection of the three-phase sinusoidal AC power supply phase. LED and buzzer indicate normal phase, reverse phase and lack of phase.
-
DX-201' -
Dexing Magnet Tech. Co., Ltd
This instrument is suitable for measuring non-magnetic stainless steel pipe inner layer accumulation rust. It can use a rechargeable battery, without power supply when test, which is suitable for outdoor environment operation. It can be used 4 hours once charge saturation. This product has been used by Hunan Xiangtan Power Generation Company Limited, Wuhan University, Nanyang Henan Yahekou Power Generation Co., Ltd., Anhui Huainan Pingwei power plants and Changsha thermal power plant, received good evaluations.
-
Model FT2 -
Gopal Electronics
Franklin Tester Model FT-2 is designed as per IS:649 & ASTM:717 Standard to measure insulation resistivity of electrical steel sheet. It requires precision & noise free DC regulated power supply and equally distributed pressure on electrode. Franklin Tester FT-2 regulated power supply provides 0.5000V with 0.1% accuracy over load and no load. Most of national and international standard has specified only 0.5%, means FT-2 is equipped with five time better accuracy than required.
-
Model LCD780 -
Gopal Electronics
3 Phase Power Analyzer LCD780 is multi-range power Analyzer with basic 0.07% R+R accuracy. 8 range of voltage, 8 range of current and total 64 range of power and power factor gives more accurate result. Harmonics Measurement Up to 31th order. USB Connectivity + Free Software. Refresh rate : 250ms / 500ms / 1000msThe gap less four-quadrant power measurement technique gives better accuracy at distorted waveforms or AC drive (VFD) operated power supply.
-
FT3151 -
HIOKI E.E. Corp
Earthing or grounding of electrical equipment is essential to maintain safety, protecting lives, as well as prevent damage to equipment. • Three-electrode method, Two-electrode method (Simple Measurement) • Wide measurement range for 0 to 1150 Ω, based on EN standard •Switchable measurement frequency to reduce the effects of power supply harmonics • Dramatically faster setup: Comes with improved grounding rods and cord winders. CAT II 300 V
-
Model 27012 -
Chroma ATE Inc.
To meet the high accuracy and low price requirements for LCM TV test device, Chroma 27012 that integrates the signal and power source provide a complete test solution for LCD Module. Its LVDS, TTL (Option) signal source fully complies with the digital signal standard, meanwhile with the 24V, 12V, 5V, 3.3V DC source output it is able to supply power to VDD, Backlight for LCM test without obtaining external power source. Equipped with the interface of single key to switch the Timing, Pattern and Program rapidly for test in auto or manual mode, the 27012 is able to provide a direct and convenient test environment for LCM TV by its complete hardware configuration and easy operation.
-
PST-3 -
Rexus Corp.
This product is design with LCD to show your ATX power voltage. Simple tester forswitching power supply. It makes it easy to test the power supply output.
-
mOByDic1700 -
Ozen Elektronik Inc.
The J1939 multiple ECU simulator provides a professional OBD development platform which allow the user to test the OBD functionality on the table. Simulates a Truck ECU . Using 5 potensiometer , 5 live data can be changed and some fixed PNG values are provided. Pressing DTC bouton the trouble codes are generated and the MIL LED is ON. DM11 commands clear the DTCs and the MIL LED. Connection to the tester is provided via a J1962 female OBD port . it needs an external 24 V power supply . More information you can get from the corresponding chipset datasheet.
-
mOByDic1010 -
Ozen Elektronik Inc.
The ISO 9141 multiple ECU simulator provides a professional OBD development platform which allow the user to test the OBD functionality on the table. Simulates 4 differnt ECUs. reading VIN and suspended DTC is possible . Using 5 potensiometer , 5 live data can be changed and some fixed PID values are provided. Pressing DTC bouton the trouble codes are generated and the MIL LED is ON. Service 4 commands clear the DTCs and the MIL LED. Connection to the tester is provided via a J1962 female OBD port . it needs an external 12 V power supply . More information you can get from the corresponding chipset datasheet.
-
UNITES Systems a.s.
VPC G12 interface - interchangeable fixturesQuick exchange of test applicationMinimum of equipment in the fixture - fixture only as contacting interfaceManual fixtures ATXFixture identification - automatic test program loadingConnection to external meas. instrumentsControled by SCADUS / LabViewSelftest of internal cards and connected instrumentsCentral test program, configuration and datalog files location possibility (server)Uninterruptible power supply for PC
-
FriedCircuits
The DC Tester is a Voltage and Ampere breakout for measuring DC current from 0-26V at 3.2A Max (when used with the USB Tester OLED Backpack). The DC jacks make it easy to measure a wide variety of devices by placing it inline between your power supply and your project without splicing cables, just like the
-
PS-200 -
CoolMax Technology Inc.
It is important to keep your graphic cards powered, but you want to make sure that your graphic cards aren’t overpowered. Not all power supply units have power surge protection, so your graphic cards may be vulnerable to damages from over voltage or over current. Protect your graphic cards now with the new PS-200.
-
SW-6 -
Lisun Electronics Inc.
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
27013 -
Chroma ATE Inc.
Chroma 27013 is a portable tester that supports high resolution and large scale LCM with the signals, power supply and test patterns required for LCD module test.
-
Rexus PST-3 -
Rexus Corp.
ATX PSU each output connectors checkTests 20-pin and 24-pin power suppliesTests SATA powerTests Pentium 4 power connectorTests PCI-Express power connectorsTests Xeon power connectorsTests Floppy drive connectorsTests standard 4-pin power supply connectorsAccurate voltage indicator +/-V(+12V1/+5V/+3.3V/5VSB/+12V2/-12V)ATX P.G value display.Lower or higher P.G values alarmLower voltage detected alarm.Over voltage alarm.No voltage detected alarm.Dimension : H * L *D : 64mm * 150mm * 18mm
